EN 
CNProducts
Heat ceramic sleeve bearing high temperature / wear resistance alumina zirconia sleeve linear
Materials：Alumina (Al2O3)/ Zirconia(ZrO2) /Si3N4 /SiC ...etc
Sizes：Custom according to the drawings
Delivery times：2 -25 days(depends on the quantity)
Precision：Ra 0.1um tolerance: 0.001mm... etc
Features：Heat resistance / Wear resistance / High purity / Refractory / High Corrosion / Good Insulation...
Customized：Can be custom for special sizes and shapes
Ceramic plates sheet substrate disc series
Ceramic Sleeve Bearing High Temperature / Wear Resistance Alumina Zirconia Sleeve LinearThe properties of ceramics
· Flexural strength · Chemical resistance · Electrical insulation · Corrosion resistance · Dielectric strength
· Wear resistance · Temperature resistance · Thermal conductivity · High voltage · Hardness...
In mechanical engineering, the type of bearing is very large, but the form of bearing used in the radiator product is classified according to its basic working principle is also three kinds: the use of sliding friction sleeve bearings (Sleeve Bearing) and the use of rolling friction ball bearings (ball Bearing) and two kinds of bearing forms to mix these three kinds.
Ceramic sleeve bearing produced by technical ceramic materials,Alumina, zirconia, silicon nitride and other ceramics
High heat and temperature resistant
The High Temperature Ceramic Sleeve have a excellent high heat temperature resistant ability. High heat ceramic sleeve can be used under 2200 ℃ high temperature environment.Coefficient of thermal expansion up to 13* 10∧6 from 20°C- 1000°C. up to 2800°C Melting point.
Wear Hardness abrasion resistant
The Wear Ceramic Sleeve is better wear and abrasion resistant property than metal. The Wear Ceramic Sleeve hardness (mohs)up to 9, HRA 80-90. Wear Ceramic Sleeve hardness is not second only to diamond, but far beyond the wear resistance of steel and stainless steel.
Precison Process Analysis of Parts
(1) Parts material: 45 steel.
The cutting processability is good.
(2) Parts composition surface: Outer Circle surface (φ50, 35, 33), inner surface (φ31.5, 20.5), type hole, two ends, inner and outer step surface, internal and external retractor groove, inner and outer chamfering.
(3) Main surface analysis: The φ20.5 inner hole is not only the supporting surface supporting other parts, but also the main datum surface of this part, and the φ50 outer Circle and its stair surface are also used to support other parts.
(4) The main technical conditions: The coaxial degree of the φ50 Outer Circle and the φ20.5 inner hole is controlled in the 0.03mm range, the vertical degree of the stair surface and the φ20.5 inner hole is controlled in the φ44 inner hole itself, the size tolerance is mm, the roughness is ra0.8μm, and the heat treatment hardness of the part is hrc50~55.
Delivery:
Custom OEM will be shipped within 15 days after determining the parameters
The samples will be shipped within 3 days
Quick Delivery Via Fedex,DHL,UPS,TNT Etc.
Support customer to designate shipping company
For more informations （the price,delivery time,moq etc）about the ceramic plates, please contact us or email:[email protected]
Machining process
Raw materials-Molding process - Sintering - Machining & Grinding - Quality Inspector
Mingrui ceramic parts property
· Flexural strength · Chemical resistance · Electrical insulation · Corrosion resistance · Dielectric strength
· Wear resistance · Temperature resistance · Thermal conductivity · High voltage · Hardness...
Ceramic materials
· 95%--99.99% Alumina (Al2O3) · Silicon Carbide · Silicon Nitride · TTZ: Magnesia partially stabilized Zirconia (ZrO2) · YTZP: Yttria partially stabilized Zirconia (ZrO2)
· ZDY: Yttria fully stabilized Zirconia (ZrO2)...
| Al2O3 | ZrO2/Y2O3 | ZrO2/MgO | MgO | SiC | Si3N4 Reaction sintered | Si3N4 Hot pressed | ALN | |
| Physical properties | ||||||||
| Density (g/cm³) | 3,9 | 5,9 | 5,75 | 3,58 | 3,2 | 3,27 | 3,29 | 3,26 |
| Molecular weight (g/mole) | 102 | - | - | 40,4 | 40,1 | 140 | 140 | 41 |
| Maximum service temperature air (°C) | 1700- 1800 | 1500 | 1000 | 2200 | 1500 | 1200- 1500 | 1100- 1600 | 1000- 1800 |
| Mechanical properties | ||||||||
| Hardness (Mohs) | 9 | - | - | 5,5 | 9 | - | - | 7 |
| Modulus of elasticity (GPa) | 300-400 | 200 | 200 | 250-300 | 420 | 170-220 | 280-310 | 318 |
| Poisson's ratio | 0,25 | - | - | 0,18 | 0,14 | 0,25-0,26 | 0,27 | 0,25 |
| Fracture toughness (MPa.m1/2) | 2-3 | 7-13 | 6-10 | - | 2,5-3,5 | 3,5-5 | 6,1 | 4,5 |
| Electrical properties | ||||||||
| Dielectric constant | 9-10 | - | - | 9-10 | - | 10 | 10 | 9,2 |
| Electrical resistivity at 20°C (Ohm.cm) | >1014 | 1013-1014 | >1010 | - | 102-106 | >107 | 1012- 1015 | >1014 |
| Dielectric strength (kV/mm) | 10-20 | 9 | 2-10 | - | - | - | - | 15 |
| Thermal properties | ||||||||
| Specific heat (J/K/kg) | 900 | 400-500 | 420 | 870-880 | 750 | 690 | 680-800 | 800 |
| Thermal conductivity (W/m/K) at 20°C | 26-35 | 2,2-3,2 | 1,5-2,5 | 40-50 | 63-155 | 9-30 | 15-43 | 180 |
| Coefficient of thermal expansion ( 10-6) from 20 to 1000°C | 8-9 | 10-11 | 5-16 | 10-13 | 4-5 | 3 | 3,3 | 4,4-5,3 |
| Melting point (°C) | 2050 | 2590 | - | 2800 | 2500 | 1900 | 1900 | 2200 |
As a ceramic plates manufacturer,us offer a wide of the ceramic specification,and customized&machinables. Get a Quote On Your Customized Now!! or up a files by EMAIL.
Our Custom Capabilities:1.High Purity Martoxid Powder
2.OEM Support, More Than 10 Technicians With 5-Year R&D Experience
3.35000 ㎡workshop, annual output could reach hundred million pieces.
4.All crafts are inspected strictly based on drawings,checked each month.
5.Best Service And Quick Delivery Via Fedex,DHL,UPS,TNT Etc.
Lead time:within 20 working days after comfirmed order. the samples within 3 days
| Technical reference of manufacture | |
| Dimensional accuracy | Up to 0.001mm |
| Concentricity | Up to 0.003mm |
| Parallelism | Up to 0.002mm |
| The inner hole tolerance | The minimum 0.005mm |
| Straight flute | The narrowest 0.1x100mm |
| The thickness of the size | Minimum to 0.02mm |
| The screw thread | Minimum internal thread M2 |
| Cylindricity | Up to 0.004mm |
| The linear tolerance | Up to 0.001mm |
| The smallest aperture | The minimum 0.07mm |
| Precision process | CNC maching,grinding,lapping |
| Surface finish | Glazed,polishing or metallized |
FAQ
1. Monthly Capacity: 50,000-60,000 pcs;
2. Material: OEM or as per your suggestion;
3. Lead time: about 7-20 days, pls confirm the quantities required;
4. Incoterm: FOB, CFR, CIF;
5. Delivery Cost: It is determinated by the destination port;
6. Payment Term: PayPal; T/T; L/C.
7. Shipment: by sea, by air, by courier, by post, etc.
Feedback
1. For any query or doubt, please contact us firstly, we will update with you soon;
2. For any other satisfaction, please also feedback to us, which could improve our service better and better.
For more information about ceramics parts,please contact our engineers in time>>>
